The question of “How to connect WIFI router to another WIFI router without wire” has brought you here and we are providing all the valid information you need in order to wirelessly connect two routers.
A wired network is simple to extend. Your network arrangement is probably similar to this: a router connected to your ISP’s modem, such as a cable modem, DSL modem, or even a high-speed FiOS line. When your router’s ports are full, just connect a network switch to one of them and begin connecting your devices to it. More devices, as well as greater distance, can now be covered if the Ethernet cable is long enough.
You need a specific setup or arrangements in order to connect two or more routers to the same home network. This setup can be rather complex and time demanding, as you’ll need to identify the best placement for both routers while also ensuring that physical connections remain functional, as well as establish your IP address settings and DHCP.
- 1 Need of connecting a second WIFI router wirelessly
- 2 Benefits of connecting a second WIFI router wirelessly
- 3 Does any of the routers have AP mode?
- 4 1st Router configuration for wireless router connection
- 5 2nd Router configuration for wireless router connection
- 6 Connecting the two routers
- 7 Using the 2nd router as a switch or access point
Need of connecting a second WIFI router wirelessly
If you’re seeking ways to use more than one router in your home, you’re probably dealing with one significant issue: bad WIFI. It’s a problem that many homes throughout the world suffer, and there are a variety of strategies to mitigate it, including employing multiple routers. In a nutshell, sure! It is feasible to use multiple routers on the same home network, but you must be cautious about how you do so.
It can be difficult to run a physical cable from one room to another in the home since it appears dirty until it is not underground. Connecting two wireless routers wirelessly not only saves cable but also the time spent in laying the physical cable and provides maintenance-free communication.
Expanding a wireless network is more difficult because wireless ranges vary depending on a variety of things such as walls, electronic interference from other devices, and the strength of your router’s wireless antenna.
Wired connections are often regarded as the most dependable and effective method of accessing the internet in your home; a wired network loses less speed than a wifi signal, and this may be the best option for you if you need the fastest speeds.
Benefits of connecting a second WIFI router wirelessly
There are various benefits of utilizing WDs Bridge to link two Wi-Fi routers without a wire. Pulling internet cable inside a home or office after construction is a significant challenge. As a result, you can use the bridge mode to wirelessly connect two Wi-Fi routers without using a physical cable and replacing it with a wireless bridge connection.
The advantages of employing several routers are based on an improvement in connectivity and performance from your home broadband. More devices in a larger area will be able to connect wirelessly, and the signal will be projected further than with a single router.
It is technical but easy to set up two wireless routers connections. It establishes a wireless access point through bridges or repeaters making a wireless connection between two wired devices or routers.
Does any of the routers have AP mode?
Before we get started on how to use two routers while only having one network, we must first understand how the second router should be configured. You can now purchase an access point, often known as a WAP, or wireless access point. This is a gadget that just serves to extend your WiFi connection.
The fundamental difference between a router and an access point is that a router can do far more than an access point. The router serves as a hub, creating a local area network and controlling all of its devices and communications. An ap, on the other hand, is a component inside a local area network that allows new devices to connect to the network and provides another direct communication path to devices.
Wireless routers can serve as access points, however not all access points may also serve as routers. While routers administer local area networks, communicate with external network systems, acquire, disseminate, and dispatch data in many directions, establish a point of communication, and provide security, access points often just provide access to the router’s established network.
Do not switch if you bought a new router and discovered that it had an AP Mode but your old router did not. The most recent router should always be the primary router in charge of all network functions. This ensures that you have new and fast hardware to handle network demands. New routers are frequently significantly more secure, which is a huge benefit given that they are connected to the internet.
1st Router configuration for wireless router connection
While this is not a required action, it is recommended because there may be settings that you have forgotten about and maybe the source of future difficulties, even if you execute the steps perfectly. To restore the router’s factory settings, press the reset button for 30 seconds.
The reset button might be one of two types: a standard button or a hole through which a paperclip is inserted to reach the switch.
Simply make sure that this router’s SSID and password match those of the second router we’ll configure. If the router hasn’t been set up yet, use an ethernet cable to connect it to your computer and plug it in. Navigate to the router’s original IP address, which is either 192.168.0.1 or 192.168.1.1. When you initially arrive, you’ll need to follow a router setup tutorial, select administrator passwords, and configure your wireless network. For this router, you must use the same SSID and password as you did for the previous one.
Configuring DHCP settings
Unless you purchased a fixed IP address, select “DHCP” or “Automatic” for the WAN type. If you purchased a static IP address, enter the IP address information precisely as provided by your ISP.
For the LAN IP, should use the gateway’s standard address. For instance, on a Linksys router, enter “192.168.1.1” for the IP address and “255.255.255.0” for the subnets to get acceptable LAN addresses ranging from 192.168.1.1 to 192.168.1.254. If you are using something besides the default IP address and subnet mask, enter it here.
Enable the DHCP server, which will provide IP addresses to new network connections. Allocate a subrange of valid LAN addresses to be assigned by the DHCP server. These are the DHCP address ranges that should be provided. Enter “192.168.1.200” to “192.168.1.254” as the DHCP range, for example.
Input the standard gateway’s address, which would be the gateway’s local identifier. As an example, enter “192.168.1.1.”
If you are using your ISP’s DNS servers, leave the two DNS server options blank or set to 0. Enter two DNS server addresses if you need to use alternate servers.
If you have a wireless router, configure the wireless settings. Give your network a name and enter it in the SSID area. Set WPA-2 encryption and a wireless password that devices must use to connect to the network. Select a channel or set the channel to “Auto.”
Changes should be saved. Disconnect the Ethernet connection from the router and the laptop. Insert an Ethernet cable into the WAN Ethernet port on the router’s back, which will be positioned off to the side, a different color, or labeled WAN. Connect the cord’s opposite end to your cable modem or DSL modem. Turn off the modem, then the router, then the modem back, wait a minute, and then re-enable the router.
2nd Router configuration for wireless router connection
You would most likely have to go through a beginning instruction where you will have to provide some data since you restarted the router. When it comes to selecting an SSID and password, use the name and password you wish for your WiFi.
Because IP addresses are unique, we’ll need to alter the IP address of this second router as well, because the first one will very certainly have the same IP address as the second. This would result in an IP conflict on your network, and it would not function as expected. Change the IP address in the router’s settings to anything else.
Set the IP address, confirm it, and then restart the router. Because you’ve changed IP, you’ll lose connection to the router, therefore go to the IP address in your browser to come back to the router settings. The only remaining step is to disable router-specific options.
Connecting the two routers
Now that both routers have been configured, there is only one little step left: connecting them. You’ll need an ethernet wire for this. The ethernet wire may need to be rather long depending on how far these routers are from each other. Yes, you can do this by connecting them wirelessly, but I recommend using a cable because both routers will be talking to one other a lot, and it’s better to have a stable connection then.
Connect the cable to one of router 1’s LAN ports, then run it across the house to the location of router 2. The setup will not work as planned if the ethernet wire is not connected to the WAN port of the second router.
You’re done once you’ve linked them both with the cable and turned them on. Congratulations, you now have two routers in your home, one of which serves as an actual router and the other as an access point, allowing you to expand your WiFi and add more ethernet connections around the house.
Using the 2nd router as a switch or access point
An additional router can support a subnetwork within a home network using the processes outlined above. This method preserves an extra layer of control over certain devices, such as imposing additional limits on their internet access.
A second router can also be set up as an Ethernet network switch or as a wireless access point. This configuration allows devices to connect to the second router as usual, but no subnetwork is created. A no-subnetwork setup is sufficient for households who want to expand basic internet access as well as enable file-and-printer sharing to more computers, but it requires a different configuration approach than the one described above.